short-circuiting

英 [ˌʃɔːt ˈsɜːkɪtɪŋ]

美 [ˌʃɔːrt ˈsɜːrkɪtɪŋ]

v.  (使)短路; (做事)抄近路，走捷径
short-circuit的现在分词

柯林斯词典

• V-ERG (使)短路
  If an electrical deviceshort-circuitsor if someone or somethingshort-circuitsit, a wrong connection or damaged wire causes electricity to travel along the wrong route and damage the device.
  1. Carbon dust and oil build up in large motors and cause them to short-circuit...
     碳尘和燃油在大发动机里越积越多，造成了发动机短路。
  2. Once inside they short-circuited the electronic security.
     一旦置入，它们就会使电子安全设施短路。
  3. Short-circuitis also a noun.
     
  4. The fire was started by an electrical short-circuit.
     火灾是由电线短路引发的。
• VERB 回避，绕过（某一流程或程序)
  If someone or somethingshort-circuitsa process or system, they avoid long or difficult parts of it and use a quicker, more direct method to achieve their aim.
  1. The approach was intended to short-circuit normal complaints procedures.
     这种方法旨在避开正常的投诉程序。

双语例句

• He found that, by charging a capacitor to various voltages and discharging it by short-circuiting it with the fuse, he could create a controlled amount of surge current.
  他发现通过电容充电到各种电压，用保险丝短路放电，可以形成一个可控的浪涌电流。
• Detection and Analysis on the arc energy of short-circuiting co_2 arc welding
  短路过渡CO2焊电弧能量的检测与分析
• Metal transfer frequency are usually taken as the criteria to evaluate the process stability of short-circuiting arc welding.
  短路过渡焊接时，熔滴过渡频率通常被作为评价焊接过程稳定性及焊接质量的重要指标。
• The rule of the arc-time and short-circuiting transfer cycle time under the high speed welding was researched by welding quality analyzer of Hannover.
  采用汉诺威焊接质量分析仪，研究了在高速焊接的情况下，燃弧时间与短路过渡周期的变化规律。
• Based on the approximate entropy theory and related algorithm, approximate entropy analysis of current in short-circuiting arc welding in CO_2 shielding gas are performed from the point of view of nonlinear time sequences.
  依据近似熵的理论和算法，从非线性角度对纯CO2保护气体条件下短路过渡电弧焊的电流信号进行了近似熵分析。
• The Finnish phone maker has received around 100 reports of its phones short-circuiting while being charged.
  芬兰手机制造商已经收到大约100份由于手机短路而被起诉的报告。
• The weld quality under different welding conditions is related to the welding parameters which are inherent electrical parameters in the welding process itself, i.e. welding current, welding voltage, arc sound, short-circuiting frequency and so on.
  不同工艺条件下的焊接质量的好坏，肯定会反映在与焊接过程本身固有的焊接工艺参数上，如焊接电流、焊接电压、电弧声压、熔滴过渡频率等等。
• The CO2 welding process needs the special external characteristic and dynamic characteristic of power source for there are alternately arcing time and short circuiting time at the period of short-circuiting CO2 welding.
  在采用短路过渡方式的CO2焊过程中，短路和燃弧过程交替发生，因此它对电源的外特性和动特性有特殊的要求。
• Multivariate statistical process control for on line monitoring of short-circuiting GMAW
  短路GMAW焊在线质量监测的多变量统计过程控制方法
• Randomicity& stability of short-circuiting droplet transfer in arc welding process
  弧焊短路过渡过程的随机性与稳定性