ejecting

英 [iˈdʒektɪŋ]

美 [iˈdʒektɪŋ]

v.  驱逐; 逐出; 赶出; 喷出; 喷射; 排出; (飞行员在飞机坠毁前从弹射座椅)弹出
eject的现在分词

柯林斯词典

• VERB 驱逐;把…逐出
  If youejectsomeonefroma place, you force them to leave.
  1. Officials used guard dogs to eject the protesters...
     官员们用警犬驱散抗议人群。
  2. He was ejected from a restaurant.
     他被逐出餐厅。
• VERB 弹出;喷出;射出
  Toejectsomething means to remove it or push it out forcefully.
  1. He aimed his rifle, fired a single shot, then ejected the spent cartridge.
     他用步枪瞄准，射出一枚子弹，然后退出空弹壳。
• VERB （通常指飞行员从即将坠毁的飞机中）弹射出来
  When a pilotejects froman aircraft, he or she leaves the aircraft quickly using an ejector seat, usually because the plane is about to crash.
  1. The pilot ejected from the plane and escaped injury.
     飞行员从飞机中弹出，安然无恙。

双语例句

• Finally, the location and size of the ejector pins that correspond to the discrete ejecting forces are obtained.
  最后，这个位置和大小的异形销，迎合了离散排出力量。
• The act or an instance of ejecting matter from the stomach through the mouth.
  胃里的东西上返从嘴中吐出的行为。
• The ejecting flying toy also comprises an afterbody form finalizing sheet which is fixed at the center of the rear part of the airfoil.
  弹射飞行玩具还包括机尾定型片，机尾定型片固定在机翼后部中央。
• Type of radioactive disintegration ( see radioactivity) in which some unstable atomic nuclei dissipate excess energy by spontaneously ejecting an alpha particle.
  放射性蜕变的一类，某些不稳定原子核自发射出一个α粒子以耗散过剩能量。
• This wave gets reflected in parts of the arterial tree and returns to the heart while it is ejecting blood, increasing the heart's workload.
  当这种波射血并增加心脏工作负荷时，它在动脉内被反射并返回心脏。
• The mixing performance of cross flow was studied in turbine ejecting mixer with tracing technique.
  采用示踪法研究了涡轮喷射混合器内错流射流混合特征。
• Some critics believe that World Cup games ought to use referees with experience ejecting superstars like Cristiano Ronaldo. '
  一些批评者认为，世界杯比赛使用的裁判一定要有把像C・罗纳尔多（CristianoRonaldo）那样的超级球星罚下场的经验。
• The Study and Calculation of Gas Filling and Ejecting Characteristics of Gas-propelled APDS
  气推式脱壳弹充排气规律研究与计算
• During an attempt at ejecting the CD magazine.
  在试图弹出CD盒期间。
• Througn designing three axial slots in internal threaded portion and optimizing nib structure, a design was made on the injection mould with a two-step ejecting mechanism with non-rotating.
  对笔尖内螺纹部分设计三段轴向开槽，优化笔尖结构，设计了二次推出不带旋转机构的自动脱螺纹注塑模。